Search found 14 matches

by luna
Wed Oct 07, 2020 7:27 am
Forum: LEONARDO 4
Topic: Error Message
Replies: 5
Views: 22

Re: Error Message

Hi Tim, I did not know that I first have to display the buildings, that results are displayed. So know I can see all results, thanks! If I want to display the surface temperature, which parameter do I have to select, is it Temperature Node 1/ outside?? What do the different nodes stand for? Kind reg...
by luna
Wed Oct 07, 2020 6:57 am
Forum: LEONARDO 4
Topic: Error Message
Replies: 5
Views: 22

Re: Error Message

Good Morning Tim!

That worked, thank you very much.

But I still can't generate the 3D-cart in Leonardo. Do I have to consider anything special for it?

Kind regards,
Luna
by luna
Tue Oct 06, 2020 2:13 pm
Forum: LEONARDO 4
Topic: Error Message
Replies: 5
Views: 22

Error Message

Hi there, I get the following error message in Leonardo when I load a file: "Acess violation at adress 00000000004138BB in module 'Leonardo4.exe'. Read of address 0000000100000021." I can still load one or two files, after that nothing works anymore and I have to reload Leonardo. What can I do about...
by luna
Thu Sep 24, 2020 12:46 pm
Forum: ENVI-met 4 (Main Simulation Model)
Topic: Adding rainfall data and using EPW
Replies: 3
Views: 164

Re: Adding rainfall data and using EPW

Hi Tim, I have another question about the Forcing Manager regarding precipitation. Assuming the precipitation of the ewp file is not 0, although I don't want precipitation. Is it enough that I do not force the precipitation? Does it become 0 if I don't set forcing as a condition in full forcing mode...
by luna
Wed Sep 02, 2020 9:06 am
Forum: ENVI-met 4 (Main Simulation Model)
Topic: Forcing file problem
Replies: 12
Views: 348

Re: Forcing file problem

Hi Tim, thanks for your resond. The measured data comes from a measuring station on a roof. That should actually meet the requirements, right? I first assumed the values from "Globalstrahlung". The simulation ran with these values without any problems, but now I am unsure. Besides, this is short- an...
by luna
Tue Sep 01, 2020 2:01 pm
Forum: ENVI-met 4 (Main Simulation Model)
Topic: Clapp and Hornberger constant
Replies: 3
Views: 146

Re: Clapp and Hornberger constant

Hi Tim,

thank you for your respond.

Do I understand correctly that the water coefficient indicates the proportion of the water content in the substrate in relation to the saturation water content? 0.5 therefore means that 50% of the saturation water content is present.

Kind regards, Luna
by luna
Tue Sep 01, 2020 12:41 pm
Forum: ENVI-met 4 (Main Simulation Model)
Topic: Forcing file problem
Replies: 12
Views: 348

Re: Forcing file problem

Hi there, I'm having trouble to identifying the correct radiation data for the full forcing manager. Since youe already worked with it, I thought someone might be able to help me. I have observed data available in German. But now I don't know which data of the full forcing manager they correspond to...
by luna
Tue Aug 25, 2020 3:18 pm
Forum: ENVI-met 4 (Main Simulation Model)
Topic: Clapp and Hornberger constant
Replies: 3
Views: 146

Clapp and Hornberger constant

Hi there, I cannot find any information on how to determine the "Clapp and Hornberger constant". I would like to know where the values from the example substrates come from. Besides I would like to know why the thermal conductivity for natural soils is determined over the Clapp and Hornberger consta...
by luna
Wed Jul 08, 2020 6:37 am
Forum: Read the forum/ manual
Topic: Full Forcing Manager
Replies: 3
Views: 295

Re: Full Forcing Manager

Good morning Laura, thank you for your helpful respond. In this context a termination of the simulation occurred. When I read in the EWP file, the simulation did not start at all. I then created a csv document with the data for the day I want to simulate. Here my first question, is this sufficient o...
by luna
Tue Jul 07, 2020 6:13 am
Forum: Read the forum/ manual
Topic: Full Forcing Manager
Replies: 3
Views: 295

Full Forcing Manager

Hi there, I have a question about the import of csv files. I uploaded weather dates from this year, but the table under the heading "Forcing File data content for each day of the year" shows this data for the year 2018. So when I wanted to start the simulation with june 2020 it's not possible becaus...
by luna
Thu Jun 25, 2020 6:50 am
Forum: Read the forum/ manual
Topic: Warning in BIO-met
Replies: 6
Views: 173

Re: Warning in BIO-met

Hi Tim,

now it's working, thank you!

Best regards,
Luna
by luna
Wed Jun 24, 2020 7:02 am
Forum: Read the forum/ manual
Topic: Warning in BIO-met
Replies: 6
Views: 173

Re: Warning in BIO-met

Hi Tim, I tried with two models and both had the same problem. They size is 50x50x30 meters and they are very simple nothing complex (without vegetation, just buildings), I just wanted to check about the calculation time and the results before I begin my actual investigation. The results should be c...
by luna
Tue Jun 23, 2020 1:46 pm
Forum: Read the forum/ manual
Topic: Warning in BIO-met
Replies: 6
Views: 173

Re: Warning in BIO-met

Hi Tim, thank you for your fast respond. I now tried to solve it with the installation of BIO-met version 1.5., but again comes the same warning. When I close the warning message, the screen in Bio-met is frozen and I have to close and re-open the program to be able to work with BIO-met again. For m...
by luna
Mon Jun 22, 2020 12:18 pm
Forum: Read the forum/ manual
Topic: Warning in BIO-met
Replies: 6
Views: 173

Warning in BIO-met

Dear Envimet-Team,

while trying to calculate in BIO-met the UTCI I received the warning: "object lock not owned". PMV and PET were no problem, just UTCI.

Do you have an advice how I can solve the problem?

Thank you.

Kind regards, Luna